Ultrasonic Spray Coating for High-Efficiency Catalyst Layers: Low-Loading Precious Metal Catalyst Deposition for Cost-Effective MEA Research

Precious-metal loading is a major design variable in polymer electrolyte membrane fuel cells and water electrolyzers. Reducing platinum or iridium use can lower material demand and help researchers investigate catalyst utilization, but low loading makes coating accuracy and measurement more demanding. Ultrasonic Spray Coating for High-Efficiency Catalyst Layers is of interest because controlled droplet deposition may support thin coatings and small research coupons. The key question is not simply whether a low nominal loading can be programmed, but whether the retained loading is uniform, measurable and electrochemically meaningful.

1. Why low-loading research is difficult

At low precious-metal mass, small errors in ink concentration, delivered volume, transfer loss or active-area definition become a large fraction of the target. A small amount of catalyst left in a syringe or feed line can materially change the retained loading. Overspray outside the masked area also affects material balance. In addition, the same absolute mass variation that is negligible for a thick electrode may be significant for a very low-loading layer.

Low-loading experiments should therefore begin with a measurement strategy. Define the target in mass per unit area, specify the active area and edge exclusion, and select a verification method with suitable sensitivity. The nominal calculation from formulation and feed rate should be treated as a process setting, not as proof of the final electrode composition.

2. Ink preparation and dosing control

Prepare catalyst ink with a documented precious-metal concentration and a reproducible dispersion procedure. Record catalyst composition, metal fraction, solvent, ionomer content, total solids and batch age. For supported platinum, distinguish total catalyst powder mass from platinum mass. For iridium oxide or supported Ir catalysts, use the appropriate elemental fraction and clearly state the basis for loading calculations.

Stable dosing requires consistent mixing and feed delivery. Sedimentation can change the metal concentration entering the nozzle even if the reservoir initially contains a homogeneous suspension. Evaluate the need for gentle agitation and confirm that agitation does not introduce bubbles or alter the ink. Check feed stability over the expected coating duration and inspect the nozzle for residue or partial blockage.

3. Process design for low retained mass

For low-loading layers, deposition may be built through multiple controlled passes rather than one heavy wet application. Pass count, traverse speed, liquid feed and path overlap should be selected to balance coverage with wet build-up. A witness coupon can be used to confirm spray footprint and track continuity. Use consistent masking and substrate positioning to prevent changes in effective area between samples.

Transfer efficiency should be defined with a clear boundary. For example, compare the metal mass retained on the intended active area with the metal mass consumed from the ink reservoir, while accounting for material remaining in lines and deposited on fixtures where practical. A high nominal transfer estimate based only on pump delivery may overlook material that never reaches the substrate. Report the calculation method and uncertainty.

4. Verifying sub-0.1 mg cm⁻² Pt and sub-0.2 mg cm⁻² Ir research targets

Targets such as below 0.1 mg cm⁻² platinum or below 0.2 mg cm⁻² iridium can be useful research design points, but they are not universal performance thresholds. Whether a layer is viable depends on catalyst activity, support, ionomer, electrode architecture and test conditions. These target values should be treated as experimental specifications to verify, not as claims of guaranteed performance or as evidence that a particular machine has achieved them.

Verification may use gravimetry where sample mass and balance resolution are adequate, or elemental analysis such as ICP-based methods when appropriate sample digestion and calibration are available. X-ray fluorescence may be useful for some substrates and loadings, but its sensitivity and matrix effects must be assessed. Choose a method with validated calibration, blanks and recovery checks. State detection and quantification limits when reporting very low metal contents.

5. Electrochemical activity validation

For Pt-containing PEMFC electrodes, ECSA and H₂/air polarization provide complementary information. ECSA should be normalized to independently verified platinum mass, and the measurement protocol should be reported. Polarization testing should control cell hardware, membrane, gas diffusion layers, compression, humidity, temperature and conditioning. At low loading, small assembly differences can dominate observed variation, so replicate MEAs are important.

For Ir-based OER layers, report the cell configuration, membrane, porous transport layer, water feed, temperature, current-density range and iR correction method. Initial activity alone is insufficient. Include a defined durability protocol and monitor voltage evolution and relevant resistance indicators. Do not infer long-term stability from a short conditioning run.

6. Interpreting performance without overclaiming

A lower loading does not automatically mean higher catalyst utilization. If the electrode becomes discontinuous or loses ionic contact, the accessible fraction may fall. If the layer is too dense, reactant transport can limit performance. Compare activity on both geometric-area and precious-metal-mass bases where scientifically appropriate, and provide uncertainty. A favorable mass activity result should be supported by loading verification and consistent test procedures.

When reporting sub-0.1 mg cm⁻² Pt or sub-0.2 mg cm⁻² Ir results, identify the specific ink, substrate, deposition route and measurement method. Do not present target values as measured outcomes unless the laboratory has independently generated and verified the data. Distinguish a planned experiment from a completed result.

7. A practical low-loading qualification sequence

Start with a stable ink and a calibrated spray footprint. Confirm the dosing repeatability on witness substrates, then coat replicate samples. Verify loading with an appropriate analytical method, map thickness or coverage, and inspect for discontinuities. Assemble MEAs under controlled conditions and compare against a suitable reference electrode. Only after the coating and measurement steps are repeatable should the team expand to more complex catalyst formulations or operating conditions.

Cheersonic’s ultrasonic coating equipment solutions and ultrasonic atomizing coating resources can help teams discuss nozzle configuration and sample-coating feasibility.

Conclusion

Low-loading precious-metal research depends on accurate ink concentration, controlled dosing, a defensible material balance and independent loading verification. Ultrasonic spraying can be evaluated as a deposition tool for these studies, but claims about utilization, activity and durability must come from measured, replicated experiments.

Qualified manufacturers, R&D teams and production engineers are invited to contact Cheersonic to discuss their coating project and arrange a sample coating test. Email: market2@cheersonic.com.