Ultrasonic Spray Coating for High-Efficiency Catalyst Layers: Emerging Applications in CO₂RR, SOEC and Anion Exchange Membrane Electrolyzers

Ultrasonic spray deposition is commonly discussed in the context of fuel-cell and PEM water-electrolysis electrodes, but its process principles are relevant to a broader range of electrochemical devices. Carbon dioxide reduction reaction (CO₂RR), solid oxide electrolysis cells (SOECs) and anion exchange membrane (AEM) electrolyzers use different catalysts, electrolytes and operating environments. Their inks and substrates therefore require distinct process development. Ultrasonic Spray Coating for High-Efficiency Catalyst Layers can provide a flexible platform for exploring these material systems, provided that the formulation and thermal or chemical constraints are respected.

1. CO₂ reduction electrodes

CO₂RR electrodes are designed to convert carbon dioxide into products such as carbon monoxide, formate or hydrocarbons, depending on catalyst composition and reactor configuration. Copper, silver, gold, tin, bismuth and other materials are studied for different product pathways. The electrode may include a catalyst layer, conductive support, ionomer or binder and a gas-diffusion substrate. Uniform catalyst distribution and controlled wetting are important because gas access, electrolyte contact and local water management influence selectivity and stability.

Ink and substrate challenges

CO₂RR inks can contain metallic nanoparticles, oxides, carbon supports, polymers or other functional additives. Their dispersion behavior varies widely. A hydrophobic gas-diffusion substrate may not wet like a hydrophilic membrane or glass coupon. Solvent selection must preserve catalyst chemistry and substrate function. A formulation that produces a continuous film on a flat witness substrate may still block gas pathways when applied to a porous gas-diffusion layer.

For ultrasonic spray trials, begin with small coupons and monitor coating mass, coverage and pore blockage. Characterize wetting and adhesion before moving to a full electrode. Electrochemical evaluation should report cell geometry, electrolyte, CO₂ flow, pressure, temperature, current density and product analysis method. Product selectivity should be measured rather than inferred from coating appearance.

2. Solid oxide electrolysis cells

SOECs operate at elevated temperatures and use ceramic or ceramic–metal functional layers. Materials may include oxide-ion conductors, perovskite electrodes, nickel-containing composites and other ceramic formulations. The coating route must account for particle size, solids loading, binder burnout, sintering behavior and thermal expansion compatibility. A sprayed green layer is only an intermediate structure; its final microstructure is determined by subsequent heat treatment.

Oxide and perovskite suspension design

Oxide and perovskite powders can have different surface chemistry and agglomeration behavior from carbon-supported electrocatalysts. Dispersants and solvents must be selected to stabilize the suspension without leaving residues that compromise sintering or electrical properties. Particle-size distribution, solids loading and binder system influence atomization and green-layer integrity. Record the full thermal profile, including ramps, holds and atmosphere, because these steps can change porosity, phase composition and interfacial bonding.

Ultrasonic spray deposition may be explored for thin functional coatings or graded ceramic layers, but the process must be compatible with the substrate’s thermal and mechanical properties. Evaluate cracking, delamination, shrinkage mismatch and interdiffusion after firing. Cross-sectional microscopy and phase analysis are important complements to surface inspection.

3. Anion exchange membrane electrolyzers

AEM electrolyzers use anion-conducting membranes and catalyst layers designed for alkaline or alkaline-like environments. They may use non-precious or reduced-precious-metal catalysts, including nickel-, iron-, cobalt- or other transition-metal-based materials, depending on the reaction and architecture. The catalyst layer must maintain ionic contact, electronic conductivity and gas or liquid transport while resisting chemical and mechanical degradation.

Ink design should consider the specific anion-exchange ionomer, catalyst surface chemistry and solvent compatibility. AEM ionomers are not interchangeable with proton-exchange ionomers. Their dispersion, wetting and alkaline stability can differ. Direct membrane coating also raises the same concerns about swelling, solvent exposure and dimensional stability discussed for PEM systems, but the material response must be evaluated for the selected AEM membrane.

4. What ultrasonic spraying contributes across these applications

Across these technologies, ultrasonic spraying can be investigated for controlled liquid delivery, patterned deposition, thin layers and flexible laboratory-scale process development. The potential value is greatest when the ink is compatible with atomization and when deposition control helps isolate the relationship between coating structure and device performance. The process does not remove the need for formulation design, substrate preparation, drying or thermal treatment.

Each application has different critical constraints. CO₂RR may prioritize gas-diffusion-layer permeability and catalyst wetting. SOEC development may prioritize green-layer uniformity and compatibility with high-temperature firing. AEM electrolyzers may prioritize ionomer compatibility and alkaline durability. A single generic spray recipe cannot address all three.

5. A qualification framework for new material systems

Begin by defining the device architecture and functional layer. Characterize powder identity, particle size, surface chemistry and solvent compatibility. Prepare a small ink matrix and evaluate stability, rheology and atomization. Coat witness substrates and the actual functional substrate. Measure mass loading, thickness, coverage, adhesion and pore or surface structure. Apply any required post-treatment, then repeat characterization to determine how the final structure differs from the as-sprayed state.

Device-level validation

For CO₂RR, combine polarization with product quantification and stability tracking. For SOECs, evaluate cell resistance, electrochemical performance and post-test microstructure under defined temperature and gas conditions. For AEM electrolyzers, control water or electrolyte feed, temperature, cell compression and gas management, and include durability tests. In every case, use replicate cells and report test conditions fully.

6. Avoiding unsupported cross-technology claims

Results from PEMFC or PEMWE coatings cannot be directly transferred to CO₂RR, SOEC or AEM systems. The catalyst, electrolyte, substrate and operating conditions are different. Likewise, the ability to atomize one ceramic suspension does not prove compatibility with another oxide powder or a different binder. Separate demonstrated results from process hypotheses, and validate each material family independently.

Cheersonic’s ultrasonic coating equipment solutions and ultrasonic atomizing coating pages offer a starting point for discussing coating concepts and sample trials with different liquid systems.

Conclusion

CO₂RR, SOEC and AEM electrolyzers broaden the potential research landscape for ultrasonic-deposited functional layers, but each application demands its own ink, substrate, post-treatment and validation strategy. A disciplined qualification workflow helps determine where ultrasonic atomization adds value without assuming that a recipe transfers unchanged between technologies.

Qualified manufacturers, R&D teams and production engineers are invited to contact Cheersonic to discuss their coating project and arrange a sample coating test. Email: market2@cheersonic.com.